Dyn'Aéro MCR01
| Dyn'Aéro MCR01 | |
|---|---|
 | |
| MCR01 'CLUB' | |
| Role | Light Aircraft / Ultralight |
| National origin | France |
| Manufacturer | Dyn'Aéro |
| First flight | July 1996 |
| Status | In production |
| Number built | 500+ |
| Developed from | Colomban MC-100 |
| Variants | Dyn'Aéro MCR4S |
The Dyn'Aéro MCR01 is a two seat, low-wing, all-composite carbon fibre light aircraft manufactured by Dyn'Aéro. It is available in kit form and ready-to-fly.
Development
The MCR01 is a variant of the Colomban MC-100 originally designed by Michel Colomban.
Variants
.jpg)
- MCR01 'VLA' (Sportster)
The MCR01 VLA (Sportster) is the JAR-VLA (Very Light Aircraft) version of the MCR, with combined flaperons, for the amateur-built category in most countries and flown with a Private Pilot Licence. The maximum speed is 318 km/h (198 mph or 172 kts) when powered by the 100 hp (75 kW) Rotax 912ULS while the stall speed in landing configuration is 87 km/h (54 mph or 47 kts). The wing of this aircraft has a chord as small as 0.80 m and an area of 5.20 m². While the early version of the kit was intended to have wings made from bonded aluminium sheet like the Colomban MC-100, this skin has been replaced with carbon fibre as can be seen on photographs shown by Dyn'Aéro Australia and New Zealand: "Note the advanced state of the wings behind the fuselage... The black colour is the natural colour of the carbon fibre before priming".[1] Nowadays, everything in the plane is made out of carbon fiber. Even rudder pedals are carbon fiber.[2] The design features a T-tail.[3] The wings of the aircraft are easlily removed from the fuselage so that the whole aircraft can be towed and stored in a trailer.
- MCR01 'CLUB'
The MCR01 CLUB is a version with a slightly bigger wing than the VLA, and meets the microlight (ultralight) regulations for Australia and New Zealand and some other countries.
- MCR01 'ULC'
The MCR01 ULC is designed to comply with the Fédération Aéronautique Internationale microlight rules. It has a 8.64 m (28.3 ft) span wing with an area of 8.13 m2 (87.5 sq ft) and a stall speed of 63 km/h (39 mph). Cruise speed is 271 km/h (168 mph) when equipped with a 80 hp (60 kW) Rotax 912UL engine.[3]
- Dyn Aero MCR-01 Banbi
- MCR '4S'
The MCR '4S' is a 4 seater version from the MCR family, and being too heavy for the ultralight class is usually registered in the homebuilt aircraft category. The MCR4s is powered by either the 100 hp (75 kW) Rotax 912ULS or the turbocharged 115 hp (86 kW) Rotax 914 and has a standard empty weight of 350 kg (772 lb) and a maximum take off weight of 750 kg (1,653 lb).[3]
Accidents and incidents
- On 18 October 2005, MCR-01 OB-1701 suffered a nose landing gear collapse while taxiing before takeoff for a training flight at Las Dunas airport (SPLH), Ica, Peru. Both pilots were uninjured. However, the aircraft suffered significant damage to the nose, engine and propeller. After investigation by the Directorate General of Civil Aviation of Peru it was found that the nose gear strut broke at a point where it was welded to the wheel bracket, and this was probably caused by a combination of fatigue, corrosion and a design fault.[4] As a result, both MCR-01 aircraft registered in Peru were grounded by the Directorate General of Civil Aviation of Peru and declared unairworthy, until a satisfactory factory redesign of the nose landing gear was made available by Dyn'Aéro. Shortly after the accident, Dyn'Aéro published a Service Bulletin to encourage MCR owners to inspect the weld joint between the front leg tube and the wheel bracket.[5] Finally, a nose gear reinforcement part was made available for mandatory installation by April 2008.[6]
- On 30 December 2007, MCR-01 G-BZXG crashed on Burgham Park Golf Course, Felton, Northumberland, United Kingdom following the detachment of the empennage in flight. The pilot and his passenger were both seriously injured. An investigation by the Air Accidents Investigation Branch revealed that some designs of attachment lugs for the all-flying tailplane had a design fault. As a result of the accident, on 6 February 2008 all MCR-01 aircraft registered in the United Kingdom were grounded by the Civil Aviation Authority until they had been inspected and new attachment lugs of stainless steel had been fitted if necessary. On 13 February 2009, Dyn'Aéro issued a Service Bulletin requiring inspection of all MCR-01 aircraft, and the replacement of attachment lugs where necessary.[7] On 22 February 2009, the French Direction Générale de l'Aviation Civile issued an Airworthiness Directive, mandating the Service Bulletin issued by Dyn'Aéro.[8]
Specifications
Data from [9]Brassey's World Aircraft & Systems Directory
General characteristics
- Capacity: 2
- Length: 5.4 m (17 ft 9 in)
- Wingspan: 6.63 m (21 ft 9 in)
- Empty weight: 235 kg (518 lb)
- Gross weight: 450 kg (992 lb)
- Powerplant: 1 × Rotax 912, 60 kW (80 hp)
Performance
- Maximum speed: 318 km/h (198 mph)
- Cruising speed: 300 km/h (186 [10] mph)
- Stall speed: 80 km/h (50 mph)
- Range: 1050 km (652 miles)
References
- ↑ Dyn'Aéro Australia and NZ
- ↑ Video presentation by DynAero - fast forward 5 min into the video
- 1 2 3 Bayerl, Robby; Martin Berkemeier; et al: World Directory of Leisure Aviation 2011-12, page 42 and 99-100. WDLA UK, Lancaster UK, 2011. ISSN 1368-485X
- ↑ "Informe Final CIAA-ACCID-009-2005" (PDF). Directorate General of Civil Aviation of Peru. September 2007. Retrieved 15 August 2011.
- ↑ "Bulletin Service N° BS 05 J 0027" (PDF). Dyn'Aéro. October 2005. Retrieved 15 August 2011.
- ↑ "Bulletin Service N° BS 08 D 0035" (PDF). Dyn'Aéro. April 2008. Retrieved 15 August 2011.
- ↑ "Bulletin Service N° BS 08 B 0034" (PDF). Dyn'Aéro. February 2008. Retrieved 15 August 2011.
- ↑ "AAIB Bulletin: 2/2009 G-BZXG EW/C2007/12/05" (PDF). Air Accidents Investigation Branch. February 2009. Retrieved 15 July 2010.
- ↑ Taylor 1996, p. 465
- ↑ "DynAero". Dyn'Aéro.
External links
 |
Wikimedia Commons has media related to Dyn'Aéro. |