National Building Code of Canada

The National Building Code of Canada is the model building code of Canada. It is issued by National Research Council Canada.^[1] As a model code, it has no legal status until it is adopted by a jurisdiction that regulates construction.

History

The Constitution of Canada includes the regulation of building construction as a provincial responsibility. In a few cases, municipalities have been given the historic right of writing their own building code. In the early years of regulating building construction, this caused a patchwork of building codes across Canada.

In 1941, the federal government of Canada published the first National Building Code. This was adopted by the various provinces and municipalities in Canada during the next 20 years.

On 1 August 1947, the Division of Building Research, later named the Institute for Research in Construction (NRC-IRC), was established to provide a research service to the construction industry and to help ensure affordable and safe housing for a growing population of Canadians. Its founding head was Robert Legget. The new organization was also given the mandate to lead the development of the National Building Code of Canada. Since then, NRC-IRC has grown to encompass emergent areas of research in support of the Canadian construction sector.^[2] Early photographs of activities are available in the archives.^[3]

The Northern Research Program was housed at the Division of Building Research over the period from 1950 to 1986,^[4] and information gleaned from the Building Materials Section in York Redoubt made its way into the Code.^[5]

Since 1960, there has been a revised document about every five years up to 1995. The 2000 edition of the building code was supposed to be an objective or performance-based building. However, this took considerably longer to write than foreseen and the next edition of the National Building Code of Canada was not published until 2005. The 2010 National Model Construction Codes was published on 29 November 2010.^[6] and the National Building Code of Canada 2010 incorporates energy efficiency requirements.^[7]

The first National Farm Building Code of Canada (NFBC) was first published in 1960. The Model National Energy Codes for Buildings and Houses were first published in 1997.^[8]

The Historical National Construction Codes on-line in PDF format is a single collection provided by the NRC of the English and French editions of all Code documents published between 1941 and 1998.^[8]

On behalf of the Canadian Commission on Building and Fire Codes (CCBFC) the National Research Council (NRC) Canadian Codes Center publishes national model codes documents that set out minimum requirements relating to their scope and objectives.^[9] These include the National Building Code, the National Fire Code, the National Plumbing Code, the National Energy Code of Canada for Buildings (NECB) and other documents. The Canadian Standards Association (CSA) publishes other model codes that address electrical, gas and elevator systems.

Requirements on the specification of structural wood products and wood building systems is set forth in the National Building Code which is concerned with health, safety, accessibility and the protection of buildings from fire or structural damage. The Code applies mainly to new construction, but also aspects of demolition, relocation, renovation and change of building use. The current NBCC was published in 2010, and is usually updated on a five-year cycle. The next update is expected in 2015.^[10]

Implementation

The National Building Code is the model building code that forms the basis for all of the provincial building codes. Some jurisdictions create their own code based on the National Building Code, other jurisdictions have adopted the National Building often with supplementary laws or regulations to the requirements in the National Building Code.

Alberta

By agreement with the National Research Council of Canada,^[11] Alberta is committed to using the National Building Code of Canada as its base document with changes and modifications to suit Alberta needs in regulating the design, construction, alteration, change of use and demolition of buildings.

The Alberta Building Code 2006 was established by the Building Technical Council, a technical council of the Safety Codes Council,^[12] after consultation with municipal authorities, provincial government departments, associations, other affected parties and Code users. The Code is published for Alberta by the National Research Council of Canada.

The Alberta Building Code 2006^[13] was adopted by provincial regulation on 2 September 2007.^[14]

The Alberta Building Code 2006 is developed and administered by Alberta Municipal and Public Affairs.^[15] In addition to the production of the Alberta Building Code, Municipal Affairs is responsible for the development and dissemination of code interpretations and alternatives known as STANDATA^[16] which come in three forms:

Building Code Variances - acceptable alternative solutions to the prescriptive requirements (known as Alternative Solutions) in Division B.
Building Code Interpretations - interpretations on Code items
Building Code Bulletins - additional explanatory information on Code items or general Code topics

British Columbia

The British Columbia Building Code^[17] is based on the core concepts of the National Building Code with some variations specific to the province. The Code applies throughout British Columbia, except for some Federal lands and the City of Vancouver.^[18] The Code is published by Crown Publications.

Vancouver

Under the Vancouver Building Bylaw, Vancouver has developed its own building code based on the National Building Code.

Ontario

The Ontario Building Code^[19] is administered by the Building and Development Branch of the Ministry of Municipal Affairs and Housing.^[20]

Prior to the enactment of the first Ontario Building Code Act in 1974, individual municipalities were responsible for developing their own building codes, resulting in a fragmented and potentially confusing regulatory environment. The introduction of a provincial Building Code Act and a provincial Building Code addressed this problem by providing for uniform construction standards across Ontario.^[21]

As of Jan. 1, 2012 the benchmark requirements for energy efficiency regarding houses and large buildings was enhanced.^[22] Updated compliance paths for energy efficiency requirements in large buildings are set out in Supplementary Standard SB-10.^[23] Residential buildings intended for occupancy on a continuing basis during the winter months must meet the performance levels specified in Supplementary Standard SB-12.^[24]

As of July 1, 2012 the Ontario Building Code was amended to address the issue of balcony glass breaking on newly constructed buildings.^[25] The new amendment, Supplementary Standard SB-13, "Glass in Guards"^[26] is intended to help minimize the likelihood that balcony glass will break on newly constructed buildings and help reduce the chance of broken pieces falling to the ground below if balcony glass does break.

Québec

The Building Act provides for the adoption of a Construction Code and a Safety Code for buildings, equipment intended for use by the public, and electric, plumbing, and pressure installations as well as installations intended to use, store, or distribute gas. Whereas the Construction Code applies to plan and estimate designers (architects, engineers, technologists) and contractors, the Safety Code is intended for owners of buildings, equipment, and facilities.

These two codes are adopted chapter by chapter and are progressively replacing the seven laws and thirty-odd regulations that were previously in effect. The goal of this process is, obviously, to simplify regulations, but also to better define the responsibilities of owners and construction professionals.

In force since November 7, 2000. The Code de construction du Quebec^[27] Consisting of the National Construction Code – 2005, amended and includes Part 10 for existing buildings.

The Quebec Code de Construction is not compulsory in the province. Municipalities have the option of adopting the code of their choice, with or without modifications. In fact, many municipalities do not have any building code officially in effect.

For example, since 2013 the regis du batiment du Québec has adopted a new code (Bill 122) that requires all owners of buildings that are 5 storeys and higher which are older than 1958 to conduct a facade inspection of the building by an engineer. This code is exclusive to the province of Québec.

Other provinces

Prince Edward Island,^[28] Nova Scotia,^[29] and Newfoundland and Labrador^[30] have legislation enforcing the current version of the National Building Code of Canada. Manitoba,^[31] New Brunswick,^[32] and Saskatchewan^[33] have adopted the 2010 National Building Code as regulations under provincial acts.

Federal jurisdiction

For most construction under federal jurisdiction the National Building Code of Canada is the applicable Code. Property under federal jurisdiction includes military bases, federal government land and airports. First Nations land (as defined by the Indian Act - land set aside for the exclusive use of First Nations) may choose to adopt the National Building & Fire Codes through a Band Resolution or By Law, however the National Building and Fire codes are not legally enforceable.

Content

The intent of the Building Code is to detail the minimum provisions acceptable to maintain the safety of buildings, with specific regard to public health, fire protection, accessibility and structural sufficiency. It is not a textbook for building design. The Building Code concerns construction, renovation, and demolition. It also covers change of use projects where the change would result in increased hazard and/or maintenance and operation in the existing building. The Code sets out technical requirements for the aforementioned project types and does not pertain to existing buildings.

The 1995 National Building Code is split into 9 parts.

Part 1 Scope and Definitions
Part 2 General Requirements
Part 3 Fire Protection, Occupant Safety and Accessibility
Part 4 Structural Design
Part 5 Environmental Separation
Part 6 Heating, Ventilating and Air-conditioning
Part 7 Plumbing Services
Part 8 Safety Measures at Construction and Demolition Sites
Part 9 Housing and Small Buildings

Part 1 gives the definitions and describes how the building code is applied. Houses and certain other small buildings (less than 3 storeys high and 600 m²) are considered "Part 9 Buildings" and only parts 1, 2, 3, 5, 6, 7, 8 and 9 apply. Larger buildings are considered "Part 3 buildings" and parts 1 through 8 apply. Part 3 is the largest and most complicated part of the building code. It is intended to be used by engineers and architects. Part 9 is very prescriptive and is intended to be able to be applied by contractors. Part 7 Plumbing Services also regulates uses for Rainwater harvesting.

The building code also references hundreds of other construction documents that are legally incorporated by reference and thus part of the enforceable code. This includes many design, material testing, installation and commissioning documents that are produced by a number of private organizations. Most prominent among these are the Canadian Electrical Code, Underwriters Laboratories of Canada^[34] a subsidiary of Underwriters Laboratories, documents on fire alarm design, and a number of National Fire Protection Association documents.

References

This article is issued from Wikipedia - version of the 11/28/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.