Sound Blaster X-Fi

Sound Blaster X-Fi XtremeGamer Fatal1ty Pro

Sound Blaster X-Fi is a lineup of sound cards in Creative's Sound Blaster series.

History

The series was launched in August 2005 as a lineup of PCI sound cards, served as the introduction for their X-Fi audio processing chip, with models ranging from XtremeMusic (lower end), to Platinum, Fatal1ty FPS, and Elite Pro (top of the range).[1]

64 MB of dedicated memory found on the Fatal1ty Pro sound card via two Micron 48LC32M8A2-75 C (PC133) SDRAM chips

The top-end Elite Pro model was aimed at musicians, bundled with the X-Fi external I/O box (offering phono with preamp inputs for turntables, high-impedance input for guitars,  1⁄4 inch mic input, headphone output, line-in, and full size MIDI I/O, as well as optical and RCA Coaxial digital inputs and outputs), and remote control.

The Platinum and Fatal1ty FPS models both offer a front-panel drive-bay control unit and remote control, while the base model was supplied without any such accessories.

All but the top model claimed 109 dB signal-to-noise ratio, while the Elite Pro model uses a higher-end DAC, with 116 dB claimed. The bottom two models feature 2 MB standard RAM, while the top models offer 64MB of X-RAM,[2] designed for use in games to store sound samples for improved gaming performance.

October 2006 saw a minor rebranding: the X-Fi XtremeMusic edition, which was in fact a highly capable gaming card, as it offers hardware decoding and EAX support, was replaced with the XtremeGamer model. The revised model featured half-width PCB, non-gold-plated connectors, optical out instead of the digital out and digital I/O module jack, and lacked the connector for users wishing to purchase a separate X-Fi I/O box. Functionality is otherwise the same.

The market segment occupied by the XtremeMusic was moved downwards, with the introduction of the (cheaper) 'Xtreme Audio' and 'Xtreme Audio Notebook' products, which, despite the "X-Fi" label, are the only products in the X-Fi line not using the EMU20K1 chip (CA20K1)[3] but an older chip similar to the Audigy SE and SB Live! cards (CA0106-WBTLF)[4] and thus lacking the hardware acceleration of 3D sound and EAX sound effects, gaming and content creation features and the I/O extensibility of all the other X-Fi models.

The other new product introduced was the X-Fi 'XtremeGamer Fatal1ty Pro', identical in function to the Fatal1ty FPS, but made more affordable by the unbundling of the I/O panel and remote control.

The 20K1 chip can use a significant amount of RAM to store sound effects for faster and improved processing, just like the previous E-mu 10K-series and E-mu 8000. This feature, dubbed X-RAM by Creative and found on the higher-end models in the X-Fi line (the Elite Pro, Fatal1ty and XtremeGamer Fatal1ty Pro Series), is claimed to offer quality improvement through audio processing capability enhancement, in addition to further reduction in host system CPU overhead.

In 2007 Consumer Electronics Show, Creative Technology unveiled PCI Express x1 and ExpressCard/34 versions of Sound Blaster X-Fi Xtreme Audio.

ExpressCard Sound Blaster X-Fi for Notebooks (34 mm with a removable plastic adapter for 54 mm slots).

X-Fi USB products

In addition to PCI and PCIe internal sound cards, Creative also released an external USB-based solution (named X-Mod) in November 2006 which is listed in the same category as the rest of the X-Fi lineup, but is only a stereo device, marketed to improve music playing from laptop computers, and with lower specifications of the internal offerings.

Other external products that use X-Fi name include USB-based Sound Blaster X-Fi HD, Sound Blaster X-Fi Surround 5.1 Pro, and Sound Blaster X-Fi Go! Pro, their internal hardware components are different for various usages and needs for gaming, surround, or audiophile standards

X-Fi features

8-channel digital-to-analog converter Cirrus Logic CS4382 placed on Sound Blaster X-Fi Fatal1ty
4-channel stereo multiplexed analog-to-digital converter Wolfson Microelectronics WM8775SEDS placed on X-Fi Fatal1ty Pro

The audio processor on X-Fi was the most powerful at its time of release, offering an extremely robust sample rate conversion (SRC) engine in addition to enhanced internal sound channel routing options and greater 3D audio enhancement capabilities. A significant portion of the audio processing unit was devoted to this resampling engine. The SRC engine was far more capable than previous Creative sound card offerings, a limitation that had been a major thorn in Creative's side. Most digital audio is sampled at 44.1 kHz, a standard no doubt related to CD-DA, while sound cards were often designed to process audio at 48 kHz. So, the 44.1 kHz audio must be resampled to 48 kHz (Creative's previous cards' DSPs operated at 48 kHz) for the audio DSP to be able to process and affect it. A poor resampling implementation introduces artifacts into the audio which can be heard, and measured as higher intermodulation distortion, within higher frequencies (generally 16 kHz and up).[5] X-Fi's resampling engine produces a near-lossless-quality result, far exceeding any known audio card DSP available at the time of release. This functionality is used not only for simple audio playback, but for several other features of the card such as the "Crystalizer", a technology that claims to improve the clarity of digital music through digital analysis (supported by all X-Fi models, including the Xtreme Audio and X-Mod).

The Sound Blaster X-Fi presents the following features, which are usually implemented with the aid of the X-Fi DSP or in software, in the Xtreme Audio model.

Since its release X-Fi has caused several unsolved problems with sound glitches on various motherboards.

Crystalizer

Creative Labs states that the primary function of the Crystalizer is to "restore portions of the sound which were lost during compression". The "compression" that is meant here is not the digital file-size reduction achieved by digital audio data compression technologies like for example mp3. Rather, the idea is to reverse the effects of dynamic range compression, an analog technique that was and is used during the production of most 1990s and newer Audio CDs (with the exception of some classical music recordings) to make them sound louder at the same volume level setting, as it was found that subjectively louder CDs get more airplay and sell better. To achieve this loudness without introducing strong distortion, points in the signal where the volume reaches a maximum are compressed (which means in this case: reduced in volume), then the whole signal is multiplied by a factor so that the maximum volume is reached again. After this, the music as a whole is louder than it was before, but the maximum volume points (mostly transients) are not as pronounced as they were before. Since this whole process is done before the final Audio CD is recorded, its effect is equally present in uncompressed audio files created from such a CD, in lossless compressed audio made from the CD, as well as in lossy compressed audio from that same CD. Transients are typically found in percussive sounds, in plosive consonants of voice recordings, and during the first few milliseconds (the so-called attack phase) of non-percussive instrument sounds. All these tend to be somewhat muffled by dynamic range compression.[6]

To undo this effect, the Crystalizer uses a multiband compander (compressor/expander) with dynamically adjusted compression/expansion. Its main function is to detect transients and to increase their relative volume level. As a consequence of enabling the Crystalizer, the signal is altered, and whether the result improves upon the input audio is purely a matter of perception and can depend on the type of audio being played.[7]

CMSS-3D

"CMSS-3D recreates realistic surround sound from any audio source and puts you right in the center of the action, whether you are using multichannel speakers or headphones." CMSS-3D is a DSP feature that provides audio enhancement. Depending on the equipment used, CMSS-3D has 3 variants:[8]

MacroFX

Enabling this setting will apply special filtering algorithms in order to improve localization for sound sources located very close to the listener.

ElevationFilter

Enabling this setting will apply special filtering algorithms in order to improve localization for sound sources located above or below the listener.

EAX effects

Environmental Audio Extensions is designed to be enabled by game developers within a game to enhance the "simulated-reality" the user is experiencing; for example, the ringing of game-world swords will sound differently depending on whether the protagonist is currently in a game-world temple vault or in a game-world open field. There are also 8 built-in EAX effects which can be enabled by the user.

SVM

This is Smart Volume Management. It is a compressor that evens out the dynamic range of any given source so that quieter sounds are louder and loud sounds are quiet. It is best used in circumstances where noise disturbance might be an issue, Late at night for instance. Otherwise it is generally preferable to have it disabled as it does make the sound less dynamic and you don't get the full impact of loud parts in films, music also sounds less lively.

Graphic Equalizer

This function divides music into ten frequency bands, which can be adjusted using the sliders.

Mixer

There are multiple volume adjustments for different inputs and outputs on the system. The master volume affects all of these settings. The default and recommended value is 50% for all sources, which actually equates to a 0 dB amplification (none), while a 100% value causes a 16 dB amplification.

MIDI support

As with many of Creative's previous sound cards, the X-Fi supports SoundFonts. Additionally, the Audio Creation Mode of the card allows the use of EAX in MIDI playback via the use of controllers.

Dolby Digital bitstream out

This setting controls the DD sound encoder.

DTS (Digital Theater Systems) bitstream out

This setting is the same as Dolby Digital Bitstream Out, only with DTS sound instead.

Operating system support

Although Creative was slow to embrace 64-bit drivers for the X-Fi lineup, most x86-64 architecture based operating systems are now supported. Microsoft Windows 7 includes basic driver support for many of the X-Fi series cards. Many of the X-Fi features however require the software applications provided by Creative in order to utilize the full capabilities of the hardware.[9]

Linux support

On September 24, 2007 Creative Labs released a closed source unsupported beta driver providing Linux 64-bit OS support for the following Sound Blaster X-Fi series sound cards:[10]

An open source driver is available with OSS v4 build 1013 and above.[11] Datasheets were provided by Creative to enable ALSA driver development.[12] On November 6, 2008 Creative finally released their driver under a GPL license.[13] It supports x86 as well as x86-64 architectures and is listed in their support area.[14] On May 15, 2009 after some communications with Creative, SUSE developer Takashi Iwai finally got a mergeable version of their X-Fi driver. On August 31, 2009 the driver (snd-ctxfi) was included in release of ALSA 1.0.21.[15] Support for Creative Sound Blaster X-Fi Titanium HD was added on January 25, 2012 in ALSA v1.0.25 release.[16]

Xtreme Audio that has a different chipset stayed unsupported for longer time. It is currently supported by advanced Linux ALSA driver modules but might require installation of additional packages from alternative repositories.[17]

X-Fi line-up

X-Fi MB

X-Fi MB is a software solution that enables basic X-Fi features on computers with integrated audio into an X-Fi device. It requires some degree of driver support from the audio hardware manufacturer. X-Fi MB is commonly bundled with motherboards and computer systems, and is comparable to an X-Fi XtremeAudio. Bundled with some Asus and ASRock motherboards, the X-Fi MB is sold as X-Fi Supreme FX and is actually a standard Analog Devices integrated HD audio codec paired with X-Fi MB. The X-Fi features are implemented entirely in the software. Other hardware vendors sell the X-Fi MB solution simply as Sound Blaster X-Fi Integrated Sound. X-Fi MB is available in different versions e.g. X-Fi MB, X-Fi MB2, X-Fi MB3 and X-Fi MB5. The current version available on select laptops and desktops is X-Fi MB5.

X-Fi Xtreme Audio

The entry-level model of the X-Fi series, the Sound Blaster X-Fi Xtreme Audio, does not actually have the EMU20K1 chip but is a re-branded Audigy SE, using the same family of chips (CA0106-WBTLF), and even the same drivers.[12] Thus, not only is all of the X-Fi–related processing performed in software, but it also lacks basic hardware acceleration just like the SB Live! 24-bit, the Audigy SE and other budget Soundblaster models. The X-Fi Xtreme Audio does not use the same drivers as the rest of the X-Fi family (and lacks ASIO), some games do not recognize it as being "X-Fi capable hardware", and the device's hardware profile resembles that of older Live! and Audigy cards.

Products in the X-Fi Family

Card Release SNR Interface Chip RAM I/O Console I/O Drive Box Remote control Notes
Elite Pro Aug '05 116 dB PCI EMU20K1 64 MB included - included Additional software included.
Fatal1ty Aug '05 109 dB PCI EMU20K1 64 MB optional included included Also known as "Fatal1ty FPS" and "Fatal1ty Edition".
Platinum Aug '05 109 dB PCI EMU20K1 2 MB optional included included
Platinum Fatal1ty Champion Aug '05 109 dB PCI EMU20K1 64 MB optional included included Rebranded "Fatal1ty" card.
XtremeMusic Aug '05 109 dB PCI EMU20K1 2 MB optional optional optional
Digital Audio Sep '05 109 dB PCI EMU20K1 2 MB optional optional optional Japan-only variant of XtremeMusic with additional jack extension.
Xtreme Audio Oct '06 104 dB PCI CA0106 - - - optional Low profile card. Does not use the EMU20K1 chipset used in the rest of the series but an old one used in the Audigy SE, Audigy Value and SB Live! 24-bit. It also has Crystallizer and CMSS-3D.
Xtreme Audio PCI Express Oct '06 108 dB PCIe CA0110 - - - optional Same as the Xtreme Audio, however in a PCIe format with a CA0110 chipset, and slightly increased SNR. Note: The CA0110 does not work on Linux with ALSA 1.0.23.
XtremeGamer Oct '06 109 dB PCI EMU20K1 2 MB - - optional Low profile card. Replacement for XtremeMusic.
XtremeGamer Fatal1ty Pro Oct '06 109 dB PCI EMU20K1 64 MB optional optional optional Essentially the Original Fatal1ty/Fatal1ty Edition/Fatal1ty FPS/Platinum Fatal1ty Champion card without the I/O drive box and remote control.
Titanium Fatal1ty Champion Jun '08 109 dB PCIe EMU20K2 64 MB - included optional
Titanium Fatal1ty Professional Jun '08 109 dB PCIe EMU20K2 64MB - optional optional Essentially a Titanium Fatal1ty Champion card without the I/O drive box.
Titanium Professional Audio PCI Express Jun '08 109 dB PCIe EMU20K2 16 MB - - optional Asia-only variant of X-Fi Titanium with minijack-to-2RCA cable and EMI shield
Titanium Sep '08 109 dB PCIe EMU20K2 16 MB - - optional First X-Fi card for which Creative made available a software-based implementation of Dolby Digital Live to allow for real-time encoding to DD 5.1 and subsequent output over the optical out port. DDL is also available for all other Titanium models.
Titanium HD Mar '10 122 dB PCIe CA20K2 64 MB optional optional Only Titanium card with no support for Windows XP. First card with THX TruStudio PC audio technology.[18] Top quality current output Burr-Brown Advanced Segment PCM1794A DAC. First stereo based internal Creative PCI/PCI-E sound card with gold plated RCA out since the ISA AWE64 Gold. Creative claims it is the highest quality ever from a Creative sound card.[19] Only available in certain markets.

See also

References

Wikimedia Commons has media related to Sound Blaster X-Fi.
This article is issued from Wikipedia - version of the 10/10/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.