Manifold (scuba)

Two 300 bar scuba cylinders connected by an isolating manifold

Face sealed manifolded twin 12l steel cylinder set

In scuba diving a manifold is used to connect two diving cylinders (tanks) containing breathing gas, providing a greater amount of gas for longer dive times or deeper dives. An isolation manifold allows the connection between the cylinders to be closed in the case of a leak from one of the cylinders or its valve or regulator, conserving the gas in the other cylinder. Diving with two or more cylinders is often associated with technical diving.

Function

Schematic diagram of scuba manifold systems

Longer and deeper dives require a greater amount of breathing gas, in turn requiring higher filling pressure, a larger cylinder or multiple cylinders. A large diameter cylinder tends to move the diver's center of mass further from the centreline, making them unbalanced in the water, and a higher pressure cylinder has a similar effect, also reducing the buoyancy of the diver, due to the thicker metal required for strength.^[1] Cylinder length is also limited by ergonomic considerations in proportion to the height of the diver. A single cylinder also presents a critical single point of failure for the breathing gas supply. Multiple-tank configurations include downstream manifolded twins, with a single regulator, independent or separate doubles which are two cylinders clamped to a backplate, but without a manifold, side mount cylinders, or manifolded twins, with two complete regulator sets.

The function of a manifold is to connect the gas supplies of two back mounted cylinders (called doubles or twins), allowing the diver to breathe simultaneously from both. The manifold is a metal tube which is connected to the cylinder valves, and may include an isolation valve or an outlet to connect a scuba regulator.^[1]

On an isolation manifold the left and right cylinder valves allow the corresponding first stage regulator to be shut off, leaving the entire gas supply to be used through the remaining regulator. The central valve, called the isolating valve, separates the tanks into two independent systems, each with its own first-stage and second-stage regulators, which can prevent a failure in one half of the system from losing the entire gas supply.^[1]

Construction

The manifold is usually machined from a high grade brass alloy,^[2] and chromium-plated for corrosion resistance and appearance. Brass is used because it is acceptably corrosion resistant, easy to machine, and suitable for oxygen service. The isolation valve uses similar materials, when present. Manifold lengths are available to connect different cylinder diameters.

Upstream manifolds

Barrel seal scuba manifold

Detail of scuba manifold showing barrel seal o-rings and left hand thread with lock nut

Manifolds intended for use with sets where a regulator is provided for each cylinder are connected to the cylinder valves upstream of the cylinder valve seat, to a connecting port provided specifically for this purpose. Two styles of connection are available for this arrangement – face seal, and barrel seal. Face seal connections are similar to the DIN regulator connection seal, and consist of an o-ring in a groove machined into the end of the manifold tube, which as clamped against the face of the valve port by a threaded component. Face seals are simple and rugged, but rely on tight connection for a reliable seal, and do not allow any adjustment for cylinder centre distance. Barrel seals use one or two O-rings in grooves around the end of the manifold tube, which seal against the bore of the valve port. They are usually screwed into the valve port with handed thread, and locked with a lock-nut. They are generally slightly less rugged than face seal manifolds, and more vulnerable to thread damage during assembly, but allow a small amount of cylinder centre distance adjustment, and provide a reliable seal even if not completely tight. Manifolds of this type are commonly supplied in sets comprising a manifold and compatible left and right side cylinder valves with a choice of neck thread specification. The working components for all three valves in the set are usually identical.

Downstream manifolds

Dräger 200 bar cylinder manifold for 170mm diameter cylinders with DIN valves

Dräger cylinder valves with manifold and reserve lever on twin 7 litre cylinders

Earlier manifolds were used to connect cylinders together downstream of the cylinder valve, using the DIN or yoke fittings on standard cylinder valves. These manifolds do not generally include an isolation valve, as the cylinder valves can be used to isolate the cylinders. However, they also do not provide for more than one regulator. Some of these earlier manifolds included a reserve valve at the connection point for the regulator.

Direct manifolds

A third style of manifold screwed directly into the cylinder neck thread, and provided a single valve which controlled flow from both cylinders to a single connector for a regulator. These manifolds could also include a reserve valve. From a gas management point of view they are identical to a single cylinder with the same capacity.

Advantages

Twin set connected by an isolating manifold

Compared to a single cylinder of equivalent capacity:

Ergonomic – Provides a more comfortable fit of cylinders with a lower profile and centre of mass closer to the diver's centreline, for better balance in the water.

Compared to independent twins:

Operational simplicity – the ability to breathe through an entire dive from a single regulator without the need to change second stages, except in an emergency or to change gases for decompression.
Only one submersible pressure gauge is necessary if the isolation valve is normally open.

Isolation manifold compared to plain manifold:

Standard malfunction management – in case of a regulator or manifold malfunction a standard procedure can be used to limit the gas loss. The diver can localize the malfunction and isolate it from the functioning system by closing the necessary valves.^[1]

Disadvantages

Compared to independent twins:

A manifold is a single point of failure for the gas supply, especially dangerous in overhead environments such as caves or wrecks. An isolating manifold localises the single point of failure to the isolating valve itself.
An upstream manifolded set must be emptied to split if needed as singles.

Compared to a single large cylinder:

The manifold, valves and second cylinder are an additional cost, both for capital outlay and maintenance.
The twin set is usually heavier than the equivalent single.

Compared to side-mount:

The manifold and valves are vulnerable to damage by impact with the overhead, and to snagging.
The valves are difficult to reach for many divers, reducing the effectiveness of isolation procedures.

Management of the manifold in gas supply emergencies

Regulator malfunction

If a regulator malfunctions on a set with an upstream manifold, the diver closes the relevant cylinder valve and switches to the other regulator. The entire remaining gas supply is available for the rest of the dive.^[1]

Cylinder connection leak

Cylinder to manifold connection malfunction, though rare, can result in an extremely violent gas loss. On a set with an isolation manifold, the diver closes the isolating valve to preserve the gas in the cylinder which is not leaking, then uses the leaking cylinder while gas remains, and switches to the intact side cylinder when the leaky one is empty. At least half of the remaining gas volume is available for the remainder of the dive. If there is no isolation valve the entire gas supply may be lost.^[1]

References

1 2 3 4 5 6 Beresford, Michael (2006). CMAS-ISA Advanced Nitrox Diver Manual (3rd ed.). CMAS-ISA.
↑ "OMS SCUBA Valves & Manifolds". OMS. 2013. Retrieved 6 May 2013.

Underwater diving

Modes	Freediving Saturation diving Scuba diving Snorkeling Surface-supplied diving

Recreational specialities	Altitude diving Cave diving Deep diving Ice diving Mixed gas diving Muck diving Open-water diving Rebreather diving Sidemount diving Solo diving Technical diving Wreck diving Underwater sports

Equipment	Backplate and wing Breathing gas Buoyancy control device Burst disc Decompression equipment Distance line/dive reel Dive computer Dive light Diver down flag Diver propulsion vehicle Diver's pump Diving air compressor Diving bell Diving chamber Diving cylinder Diving equipment Diving helmet Diving regulator Diving shot Diving suit Diving weighting system Dry suit Fins Full face diving mask Integrated Diver Display Mask Lifting bag Line marker Mask Moon pool Pony bottle Rash vest Rebreather Scuba manifold Scuba set Snoopy loop Snorkel Snuba Surface marker buoy Testing and inspection of diving cylinders Towboard Vintage scuba Wetsuit

Applications	Clearance diver Commercial offshore diving Diver training Frogman Military diving units Police diving Professional diving Public safety diving Recreational diving Saturation diving Scientific diving Underwater archaeology Underwater photography Underwater videography

Hazards	Barotrauma Decompression sickness Deep water blackout Drowning Dysbaric osteonecrosis High-pressure nervous syndrome Human factors in diving safety Hypercapnia Hypothermia Isobaric counterdiffusion List of diving hazards and precautions List of signs and symptoms of diving disorders Nitrogen narcosis Oxygen toxicity Scuba diving fatalities Seasickness Shallow water blackout Silt out Task loading

Procedures	Ascending and descending (diving) Buddy breathing Buddy diving Controlled buoyant lift Controlled emergency swimming ascent Decompression (diving) Decompression practice Dive planning Diver communications Diver navigation Diver rescue Diver trim Dive log Drift diving Emergency ascent Night diving Penetration diving Pyle stop Recreational diver training diver certification Diamond Reef System Rule of thirds (diving) Scuba gas planning Scuba skills Solo diving Underwater search and recovery Underwater searches

History	History of decompression research and development Researchers in underwater diving Timeline of diving technology

Categories: Diving equipment Professional diving Recreational diving Underwater diving history Underwater diving procedures Underwater diving safety Commons Glossary Portal

This article is issued from Wikipedia - version of the 6/23/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.